Category
Recently Viewed Products
-
AS R26
$38.00$22.80 -
AS R3
$48.11$28.87 -
AS S1
$54.77$32.87 -
ASTM E3069
$50.00$30.00 -
AWS A5.01M/A5.01
$79.00$47.40
ULC 102.2
$250.00 $150.00
Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings, and Miscellaneous Materials and Assemblies (ULC S102.2)
standard by Underwriters Laboratories of Canada, 06/01/2018
ULC 102.2 – Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings, and Miscellaneous Materials and Assemblies (ULC S102.2)
Product Details
- Edition:
- 8
- Published:
- 06/01/2018
- Note:
- This product is unavailable in Ukraine, Russia, Belarus
Related products
-
ULC 9705
$264.00$158.40Add to cartFire Tests – Full Scale Room Test for Surface Products (CAN/ULC 9705-13)
standard by Underwriters Laboratories of Canada, 03/01/2013 -
ULC 718
$50.00$30.00Add to cartSite Quality Assurance Program For Spray Polyurethane Foam
standard by Underwriters Laboratories of Canada, 2018 -
ULC 774
$270.00$162.00Add to cartStandard Laboratory Guide for the Determination of Volatile Organic Compound Emissions from Polyurethane Foam (CAN/ULC S774)
standard by Underwriters Laboratories of Canada, 03/17/2020 -
ULC 717.1
$175.00$105.00Add to cartStandard for Flat Wall Insulating Concrete Form (ICF) Units
standard by Underwriters Laboratories of Canada, 11/01/2017
ULC 102.2
$238.00 $142.80
Method of Test for Surface Burning Characteristics of Flooring, Floor Coverings, and Miscellaneous Materials and Assemblies (CAN/ULC S102.2-10)
standard by Underwriters Laboratories of Canada, 07/01/2010
This Standard is applicable to the finished surface or covering of a floor extending to a maximum depth of 65 mm. This method is also applicable to the following:
- A Materials which cannot be tested to CAN/ULC-S102, without the use of supporting material that is not representative of the intended installation;
- B Materials which, when tested to CAN/ULC-S102, melts or drips, or otherwise disintegrates and continues to burn on the floor of the test chamber;
- C Materials designed for use in a relatively horizontal position with only its top surface exposed to air; or
- D Thermoplastic materials.
Where a material cannot be readily determined to be thermoplastic or thermoset, one test is conducted in accordance with this standard and one additional test in conformance with requirements of CAN/ULC-S102, Standard Method of Test for Surface Burning Characteristics of Building Materials and Assemblies.
The primary purpose of the Standard is to determine the comparative burning characteristics of the material or assembly under test by evaluating the flame spread over its surface when exposed to a test fire and thus establish a basis on which surface burning characteristics of different materials or assemblies may be compared, without specific considerations of all the end-use parameters that might affect these characteristics.
It is the intent of this Standard to register performance during the period of exposure, and not to determine suitability for use after the test exposure.
Product Details
- Edition:
- 7
- Published:
- 07/01/2010
- Note:
- This product is unavailable in Ukraine, Russia, Belarus
Related products
-
ULC 842
$631.00$378.60Add to cartGuide for the Investigation of Valves for Flammable and Combustible Liquids
standard by Underwriters Laboratories of Canada, 08/25/2020 -
ULC 716.2
$223.00$133.80Add to cartStandard for Exterior Insulation and Finish Systems (EIFS) – Installation
standard by Underwriters Laboratories of Canada, 2019 -
ULC 801
$200.00$120.00Add to cartStandard on Electric Utility Workplace Electrical Safety for Generation, Transmission and Distribution (CAN/ULC S801-14)
standard by Underwriters Laboratories of Canada, 2014 -
ULC 8753
$264.00$158.40Add to cartStandard for Field-Replaceable Light Emitting Diode (LED) Light Engines (CAN/ULC S8753)
standard by Underwriters Laboratories of Canada, 2013